Appmuse

Allows for East profile swaps if I open a window. Allows removal of mid frequency correction and high frequency adjustment. Allows checking of bass correction. If this won’t run, try reverting the AVR vanity name to default. Show more

Many have written Denon and Marantz support about an issue with speaker timing. The AVRs have the speed of sound coded as 300 m/s instead of the true speed. Of 343 m/s. To fix this, you have to manually multiply all speaker distances by 0.875. When I did that, WOW - everything snapped in to place and objects moving around the room sounded so much better. Audyssey themselves understand this issue and have addressed it in their -X desktop software ($199 per AVR license). Two things Sound United can do that so far refuse. One - update this app to automatically adjust the speaker distances so the processor will get the timing right. This would seem to be the quickest and easiest and be done first. Second is update the firmware in the AVRs with the correct speed of sound number. This isn’t rocket science and Sound United’s deafness on this issue is baffling. Show more

This editing app works as described with my Denon AVR S960H. Being able to see the “Before” room correction graphs allowed me to decide which speakers to keep or remove the midrange compensation by the speakers native dip around the 2khz range. I could also use the curve editor to give a slight bump in the dual subwoofer’s 25-50hz range to add just a little more punch to the deep frequencies. Being my living room isn’t the most optimum for speaker placement, I let the EQ Frequency Range setting edit the room correction at full 20-20,000hz range, rather than cutting it off near the 500hz range like many do. Using this app rather than the one built into the AVR has made a noticeable difference in sound quality, and was worth the reasonable cost. It was almost like removing a blanket off the speakers. Show more

The graphic EQ is only 9 bands. This doesn’t allow you the ability to fix critical room issues. There should be an expert mode that enables a 29 band EQ. This would be on par with pro audio graphic EQs. Show more

.. though I wonder why I cannot download and view a calibration that was created with the receiver…? I can only see curves produced with this app. Frustrating.

Why????????? It was fine before!

Can’t get through the setup without getting a communication error. It doesn’t save progress so you have to restart every time. Receiver is wired, phone is less than 5’ from router. Network is rock solid for everything else. Go on the audio forums, this is a common issue that they haven’t addressed for 5 years. The app is useless if you can’t get through setup. Don’t waste your money on this garbage. Show more

I’ve been using this app for a while now. Much better than calibration using the receiver. The flexibility to edit different things in copies and upload them is a great way to test different settings. Love it. No problems with my iPhone. Show more

I see people giving a low star for too much noise and other problems, but first thing. Turn off any eco mode on your Denon or Marantz before calibration. You’ll thank me later. This app is A nice complement to any Denon or Marantz receivers. If you can buy a 2k-3k receiver then this $20 app shouldn’t be an issue. Show more

It says error 1. Communication error when trying to send file. Tried Wi-Fi, Ethernet, reinstalling app. Nothing works. Absolute garbage

My setup is in a small room and getting the sound tuned to my liking has been a journey but this app helped me run the setup much better than without it and the sound improvements are very noticeable so no complaints. Show more

The first time I tried to use the app after all positions received an error unable to save curves, try again. Was not able to save and had to cancel. I now have to start all over is there a app update? Show more

Definitely better correction with this app however I’ve had to reset the AVR every time I want to load a new preset.

Just got a brand new Denon 1700 AVR and despite running the original MultEQ setup the sound was muffled and lacked good sound. This is a system with Paradigm speakers, so I knew right away it was something in the setup of the AVR. Lots of research brought me to this app-well worth the 20 bucks and it worked flawlessly for me. Not sure why it’s buggy on other peoples phones but it worked right out of the gate for me. The better comment is WOW I had no idea that moving a few curves around and adjusting some settings in this app would make my system sound COMPLETELY different. It’s amazing how the clarity and spatial sound is back in my system. It works, period. Show more

I can’t get past the first position anymore without the system having issues. It happens when it’s playing the sub notes and then tries to go to second position when it’s still playing the sub levels for position 1. Then I can’t get it to even attempt at a second position. It says too much noise. I’ve done this many times before and same noise level in the house. It just won’t get past that first measurement anymore. Not sure what’s going on this is after two days of trying. Deleted the app. Tried on my phones app. Same thing. Unplugged the receiver for 30 seconds and tried again. Same issue. Please update the app to work again so I can put things away in my house. Show more

I have a Denon AVR 3600. I tried seven times to complete just one calibration and was ultimately unsuccessful. Even when I left the microphone in the same position for all of the tests, it would eventually encounter a noise/speaker level error even though there were no differences from prior tests in an empty house with HVAC breaker turned off. If there was a perceived problem with one speaker reading during one position test, the app would show an error message and asked me to redo the test…but the test would never rerun and I got stuck every time without being able to get through all 8 test positions. I am extremely frustrated to have spent two hours trying to get this to work and not have one single room calibration from the effort. Show more

This app takes care of room acoustics for anything from stereo to surround sound. Flexible - a number of presets are available for midrange harshness compensation and level adjustments for individual speakers. Takes the receiver to a whole new level for clarity and imaging. Show more

What a joke of an app. Terrible control, next to no info of what any of the processes are actually doing. A literal scam for how much they are charging. Should be free for how little you get from the app. I feel absolutely ripped off. Show more

Update: raised rating to 3 stars; iPadOS15 crash is fixed. Only recent change is IOS and iPadOS 15. Audyssey app crashes immediately when adding a new curve. Power cycled receiver (AVR-4500) with front panel and power cord; reinstalled app; verified network connection; power cycled iPad. No improvement. Show more

The latest version crashes each time I try to connect to my AVR, whether that’s to run a new calibration and send one to the presets. When it works the app is well worth the money, but I fear this problem will persist and won’t be addressed. Show more